Blackpro:
The Blackpro software has been developped especially for the Blackprog programmer. The software will take care of mode switching during programming fully automatic. And on top of that, the Blackpro software has some very nice features that will allow you to test/analyze your Titanium cards before programming.














CardMaster:
The CardMaster software will only work with the Chipdrive Mini, Mini Millenium & some VX-Multi programmers.















CardPro:
The CardPro software will only work with the CardPro & ISO-7816 programmers.
















CardWriter:
The CardWriter software will work with all Universal programmers.
















ChipCat:
The ChipCat software will work with all Universal programmers.

















DMSSC:
The DMSSC (or SCprog) software will work with all Universal programmers.

















FunMagic:
FunMagic can be used in 2 ways:
1. as a fun programmer software
2. as funcard eeprom editing software

If used as fun programmer software, you will need a parallel fun programmer or Apollo programmer. You can then program the Flash, Internal Eeprom & External Eeprom with this software.

If used as a funcard eeprom editing software, you need to connect to a Phoenix interface. You can then edit the External Eeprom on a funcard with this software. You need to set the size of the External Eeprom in the Apollo menu.










FunProm:
FunProm is only capable of programming funcards thru the use of a parallel fun programmer. You can program the Flash, Internal Eeprom and External Eeprom with FunProm.

For External Eeproms bigger than 64Kbit, there is a special version, called FunProm128-256. This version allows editing and programming of External Eeproms of up to 256Kbit.












GoldMate PC:
The GoldMate PC software will work with the GoldMate PC programmer only.
















Gold*Card:
The Gold*Card software will work with the GoldProg & Millenium programmers only.

















ICprog:
The ICprog software will work with a wide range of programmers: both Universal and Other programmers.
ICprog allows you to program a wide variety of Processors.
External Eeproms are no problem for ICprog either. The only problem you will most likely encounter, is to find a proper loader file to load the External Eeprom through the Processor.
















Infinity:
The Infinity software will only work with the InfinityUSB programmer.


















MasterBurner:
The MasterBurner software will work with all Universal programmers. If your programmer is not listed in the configuration menu, then select the MasterCRD-LC as your programmer, and MB will allow you to switch manually.

















MiniSDK:
The MiniSDK software will only work with the MiniSDK programmer.
















MKFind:
For MKFind, a Phoenix interface is required. So you will need any programmer that supports a genuine Phoenix mode.

















MultiProg:
The MultiProg software is written solely for use with the Elvis (MultiPro 3.4/3.5) programmer.

















TwoProg:
TwoProg can only be used in combination with the Multiprog 2001 XL programmer.



















Blackprog:
The Blackprog programmer works perfectly with this software:
- Blackpro software
- MOSC software














CardMaster USB:
The CardMaster USB can only be operated with the CardMaster software.
This programmer is not suitable for editing MOSC cards, nor for direct editing of external Eeproms.













Chipdrive Gold:
The Chipdrive Gold works fine with this software:
- ChipCat
- MOSC software.












Chipdrive Mini/Mini Millenium:
The Chipdrive Mini/Mini Millenium is available in 2 different versions:
- firmware revisions without funcard support
- firmware revisions with funcard support (from version 100)

I have not got a version with funcard support, so I cannot garantuee that it will work.
The Chipdrive Mini/Mini Millenium works with this software only:
- CardMaster









CLaNZeRS MiniSDK programmer:
The MiniSDK will program all common cards.
Direct editing of the eeprom on a card is possible with this device through both a Phoenix interface and a Smartmouse interface. You have the following choice of programming software:
- The original MiniSDK software
- TJ's excellent software for the MiniSDK
- You can also use any software that uses Phoenix or Smartmouse interfacing












Digitech USB programmer:
The Digitech USB will program all common cards.
Direct editing of cards through a Phoenix interface is not possible with this device though. The Digitech USB is connected to your PC (as it's name suggests) via the USB port. And as there is no software for editing cards via USB, there is no possibility to edit a card directly.
So if you want to edit MOSC cards, or edit keys directly on your card with software like ISVedit, you will still need a real Phoenix interface, connected to a COM port.











Elvis of Multiprogrammer 3.4/3.5:
The Elvis works fine with this software:
- TJ's Multiprog
- MOSC software












Funprog:
The Funprog works fine with this software:
- FunProm
- FunMagic













Funprogrammer USB:
The Funprogrammer USB will program all common AVR type cards (Jupiter, Fun & AT Mega).
Direct editing of cards through a Phoenix interface is not possible with this device though. The Funprogrammer USB is connected to your PC (as it's name suggests) via the USB port. And as there is no software for editing cards via USB, there is no possibility to edit a card directly.















GoldProg of Millenium:
The GoldProg and Millenium work fine with this software:
- Gold*Card (Gold 140)














GoldMate PC:
The GoldMate PC can only be operated via the GoldMate PC software.














Infinity USB programmer:
The Infinity USB will program all common cards.
Direct editing of cards through a Phoenix interface is not possible with this device though. The Infinity USB is connected to your PC (as it's name suggests) via the USB port. And as there is no software for editing cards via USB, there is no possibility to edit a card directly.
So if you want to edit MOSC cards, or edit keys directly on your card with software like ISVedit, you will still need a real Phoenix interface, connected to a COM port.












Infinity USB Phoenix programmer:
The Infinity USB will program all common cards.
Direct editing of cards through a Phoenix/Smartmouse interface is now also possible with this device, thanks to its dual interface capabilities. The Infinity USB Phoenix is connected to your PC (as it's name suggests) via the USB port AND via the Serial port.













ISO 7816:
The ISO 7816 works fine with this software:
- CardPro
- ChipCat
- MOSC software













JDM programmer:
If you only have a JDM programmer, then your options are limited. You can program about every possible processor on any popular card, but the Eeprom on the card will, in most cases, be impossible. You can only program the Eeprom on a card if it is directly addressable. In other words, the card will have to be equiped with direct programming lines. That means that all plastic cards are out of the question for the JDM.
However, if you also have a Phoenix interface or a Smartmouse Interface, then suddenly you have a lot of options and possibilities. You just need to connect the JDM and the Phoenix (or Smartmouse) alternately. The software will tell you when. In ChipCat it is even possible to configure 2 different programmers on two different COM ports. That means that you can connect the JDM to COM 1 and the Phoenix or Smartmouse to COM 2 simultaneous.







MasterA/VX-Multi :
The MasterA's and VX-Multi's work fine with this software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner
- MOSC software










MasterCRD :
The MasterCRD's work fine with this software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner
- MOSC software











MasterUSB programmer:
The MasterUSB will program all common AVR type cards. The number of PIC type cards, programmable with the MasterUSB is limited to Goldcards and Silvercards.
Direct editing of cards through a Phoenix interface is not possible with this device though. The MasterUSB is connected to your PC (as it's name suggests) via the USB port. And as there is no software for editing cards via USB, there is no possibility to edit a card directly.
So if you want to edit MOSC cards, or edit keys directly on your card with software like ISVedit, you will still need a real Phoenix interface, connected to a COM port.













MasterUSB Plus programmer:
The MasterUSB Plus will program all common AVR type cards. The number of PIC type cards, programmable with the MasterUSB Plus is limited to Goldcards and Silvercards.
Direct editing of cards through a Phoenix interface is not possible with this device though. The MasterUSB Plus is connected to your PC (as it's name suggests) via the USB port. And as there is no software for editing cards via USB, there is no possibility to edit a card directly.
So if you want to edit MOSC cards, or edit keys directly on your card with software like ISVedit, you will still need a real Phoenix interface, connected to a COM port.













MaxKing SLA-XL :
The MaxKing SLA-XL works fine with this software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner
- MOSC software











Millenium Micro 106:
The Millenium Micro 106 can only be operated with the CardMaster software.
This programmer is not suitable for direct editing of MOSC cards, nor for direct editing/writing of the external Eeprom on your card.













Millenium Micro 206:
The Millenium Micro 106 can only be operated with the CardMaster software.
This programmer is not suitable for direct editing of MOSC cards, nor for direct editing/writing of the external Eeprom on your card.













Multipro:
The MultiPro works fine with this software:
- CardPro
- ChipCat
- MOSC software












Multipro USB:
The MultiPro USB works fine with this software:
- CardPro














Multiprog 2001 XL:
The Multiprog 2001 XL works fine with this software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner
- Twoprog
- MOSC software











NeonProg 500:
The NeonProg 500 works fine with this software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner
- MOSC software











Phoenix interface:
It is NOT possible to program the processor on a card with a Phoenix interface. So if you want to program a complete card, you will need an extra programmer that is capable of programming the cards processor (like the JDM f.i.). With such a combination, you can use the following software:
- ChipCat

The Phoenix is great for reading and/or editing your MOSC cards. Provided you are using the proper software of course. But also Eeprom data maintenance directly on the card is something the Phoenix can be used for. Most editing software, like ISVedit and Picbined for instance, can read and modify the Eeprom content directly through the Phoenix or Smartmouse interface.










SC-Master :
The SC-Masters work fine with this software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner
- MOSC software
- SC-Quickburner











Smartmouse interface:
It is NOT possible to program the processor on a card with a Phoenix interface. So if you want to program a complete card, you will need an extra programmer that is capable of programming the cards processor (like the JDM f.i.). With such a combination, you can use the following software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner

The Smartmouse interface is great for Eeprom data maintenance directly on the card. Most editing software, like ISVedit and Picbined for instance, can read and modify the Eeprom content directly through the Phoenix or Smartmouse interface.










Towitoko Chipdrive:
The Towitoko Chipdrive is supplied complete with software.
Software for editing GSM cards among others.
As far as I know, there is no software for editing satellite viewing cards with the Towitoko Chipdrive.













VP-20/DL-20:
The VP-20/DL-20 works fine with this software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner
- MOSC software













VP-30:
The VP-30 works fine with this software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner
- MOSC software












The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- ChipCat
- DMSSC
















The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- ChipCat
- DMSSC















The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner


















The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner














The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner
- Twoprog

















The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- ChipCat
- DMSSC
- MasterBurner
- Twoprog

















The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- DMSSC


















The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- DMSSC

















The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- DMSSC
- MasterBurner
















The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- DMSSC
- MasterBurner
















The selected combination of Programmer and Card, gives you this choice of software:
- DMSSC
- Twoprog


















The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- DMSSC
- Twoprog

















The selected combination of Programmer and Card, gives you this choice of software:
- CardWriter
- DMSSC
- Twoprog
















The selected combination of Programmer and Card, gives you this choice of software:
- DMSSC
- MasterBurner

















The selected combination of Programmer and Card, gives you this choice of software:
- DMSSC
- MasterBurner


















The selected combination of Programmer and Card, gives you this choice of software:
- FunProm
- FunMagic


















The selected combination of Programmer and Card, gives you this choice of software:
- FunProm128-256 (works exactly like FunProm)
- FunMagic